PS3 YLoD Motherboard Repair Guide, With Gilksy Videos. As our consoles are forced to do more and more each generation, we are seeing a decrease in their. Using the Gilksy Guide, I successfully fixed the “Yellow Light of Death” (YLOD) on my old 60Gb PS3. All I needed was the following items. I had offered to fix a PS3 that suffered from the YLOD (Yellow Light Of .. GILKSY REFLOW + FLUX + CLAMP BEND (THE NUMBER ONE.
|Published (Last):||16 December 2005|
|PDF File Size:||16.16 Mb|
|ePub File Size:||10.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
As our consoles are forced to do more and more each generation, we are seeing a decrease in their expected life expectancy.
Do you already have an account? Hinge case towards you until disengaged and then tilt towards the ylox. Remove all Phillips screws marked noting size and position. Make sure to reconnect the ribbon cables securely, I accidentally didn’t make a solid connection on two of them which gave me a few headaches.
Log in or Sign up. Anyways, I tried to turn it back on but my ps3 had the yellow light of death.
Repairing a PlayStation 3 with the Yellow Light of Death (YLOD)
gilsy This will invalidate any warranty. All parts have been dismantled and hoovered out plus I’ve just finished removing the thermal paste from everywhere too.
YLOD is refered to by Sony as a general hardware failure. Place motherboard on a baking dish so that it lies flat, place in the oven for 10 minutes, then yllod and let cool for 45 minutes.
His six part guide is also accompanied by a PDF but what most posters miss is the additional flux and clamp bending video. Typical example of dust build up.
PS3 YLoD Motherboard Repair Guide, With Gilksy Videos
All I needed was ls3 following items: No, create an account now. After 10 to 15 seconds move onto the next area. Isopropyl alcohol acquire from chemist. A member of staff at my local game store golksy mastered a method of using two paper clips fashioned to go into the drive slot and ps33 the disc and pull out. CrazyGamer Follow Forum Posts: There were others that used a hairdryer to heat up the warranty seal and take a blade to remove it, then stick it to wax paper and disassembled the system, repaired it and put the sticker back on so they weren’t hindered by the options lost after breaking the seal.
A yellow light that signifies a significant hardware failure, replacing the normal green power indicator on the ps3. Other cleaners may be substituted.
Yellow light of Death PS3 help!
Yes, my password is: My game store also mentioned that I should remove the HDD before sending the console back to Sony because there have been many cases of Sony sending consoles back with wiped HDDs. Source There is also the issue of flux contained in solder. Results 1 to 10 of The YLOD has struck again! You must log in or sign up to reply here. Once you’ve isolated the motherboard, remove all cables and heatsink rubbers. Pair that with the fact you can buy a brand spanking new console for a little more Use syringe supplied and dispense a small worm of compound from top to bottom on the left hand side of processor chip, now using credit card supplied spread compound evenly and thinly over processor face to much is bad and not enough is also bad the ideal amount is when you can almost see through the paste.
If however your system has needed to be reflowed a second or more times you will probably need to flux the BGA’s in order to acheive positive results from the reflow. Bring back the main forum list.
Attempt a recommended repair that seems to get the longest results. Additional cables and controllers may not find their way back to you.
Based off of our results we have mainly fid this repair to be able to go in and recover data and deactivate systems. There are way thermal pastes that don’t conduct electricity. Heat sink rubber pads still on in this picture remove before reflowing also hold ribbons out of way while reflowing Congratulations!!
Supporting fan assembly turn board over, remove fan power connector and fan.
Repairing a PlayStation 3 with the Yellow Light of Death (YLOD) – Blog
Here’s a useful explination of that method I found: Heat sink compound still on in this picture, remove before reflowing. All credit for this repair goes to gilksy for his excellent work and development of this repair technique.
I also found posts about people successfully fishing their discs out with a pair of tweezers. Oct 25, Posts: Senture Wise Guy Joined: